IR Sensor, PanicButton, OneWireTempSensor

[svn42.git] / rf433ctl / DallasTemperature / examples / Multiple / Multiple.pde

diff --git a/rf433ctl/DallasTemperature/examples/Multiple/Multiple.pde b/rf433ctl/DallasTemperature/examples/Multiple/Multiple.pde
new file mode 100644 (file)
index 0000000..2694d07
--- /dev/null
+++ b/rf433ctl/DallasTemperature/examples/Multiple/Multiple.pde
@@ -0,0 +1,140 @@
+#include <OneWire.h>
+#include <DallasTemperature.h>
+
+// Data wire is plugged into port 2 on the Arduino
+#define ONE_WIRE_BUS 3
+#define TEMPERATURE_PRECISION 9
+
+// Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
+OneWire oneWire(ONE_WIRE_BUS);
+
+// Pass our oneWire reference to Dallas Temperature. 
+DallasTemperature sensors(&oneWire);
+
+// arrays to hold device addresses
+DeviceAddress insideThermometer, outsideThermometer;
+
+void setup(void)
+{
+  // start serial port
+  Serial.begin(9600);
+  Serial.println("Dallas Temperature IC Control Library Demo");
+
+  // Start up the library
+  sensors.begin();
+
+  // locate devices on the bus
+  Serial.print("Locating devices...");
+  Serial.print("Found ");
+  Serial.print(sensors.getDeviceCount(), DEC);
+  Serial.println(" devices.");
+
+  // report parasite power requirements
+  Serial.print("Parasite power is: "); 
+  if (sensors.isParasitePowerMode()) Serial.println("ON");
+  else Serial.println("OFF");
+
+  // assign address manually.  the addresses below will beed to be changed
+  // to valid device addresses on your bus.  device address can be retrieved
+  // by using either oneWire.search(deviceAddress) or individually via
+  // sensors.getAddress(deviceAddress, index)
+  //insideThermometer = { 0x28, 0x1D, 0x39, 0x31, 0x2, 0x0, 0x0, 0xF0 };
+  //outsideThermometer   = { 0x28, 0x3F, 0x1C, 0x31, 0x2, 0x0, 0x0, 0x2 };
+
+  // search for devices on the bus and assign based on an index.  ideally,
+  // you would do this to initially discover addresses on the bus and then 
+  // use those addresses and manually assign them (see above) once you know 
+  // the devices on your bus (and assuming they don't change).
+  // 
+  // method 1: by index
+  if (!sensors.getAddress(insideThermometer, 0)) Serial.println("Unable to find address for Device 0"); 
+  if (!sensors.getAddress(outsideThermometer, 1)) Serial.println("Unable to find address for Device 1"); 
+
+  // method 2: search()
+  // search() looks for the next device. Returns 1 if a new address has been
+  // returned. A zero might mean that the bus is shorted, there are no devices, 
+  // or you have already retrieved all of them.  It might be a good idea to 
+  // check the CRC to make sure you didn't get garbage.  The order is 
+  // deterministic. You will always get the same devices in the same order
+  //
+  // Must be called before search()
+  //oneWire.reset_search();
+  // assigns the first address found to insideThermometer
+  //if (!oneWire.search(insideThermometer)) Serial.println("Unable to find address for insideThermometer");
+  // assigns the seconds address found to outsideThermometer
+  //if (!oneWire.search(outsideThermometer)) Serial.println("Unable to find address for outsideThermometer");
+
+  // show the addresses we found on the bus
+  Serial.print("Device 0 Address: ");
+  printAddress(insideThermometer);
+  Serial.println();
+
+  Serial.print("Device 1 Address: ");
+  printAddress(outsideThermometer);
+  Serial.println();
+
+  // set the resolution to 9 bit
+  sensors.setResolution(insideThermometer, 9);
+  sensors.setResolution(outsideThermometer, 9);
+
+  Serial.print("Device 0 Resolution: ");
+  Serial.print(sensors.getResolution(insideThermometer), DEC); 
+  Serial.println();
+
+  Serial.print("Device 1 Resolution: ");
+  Serial.print(sensors.getResolution(outsideThermometer), DEC); 
+  Serial.println();
+}
+
+// function to print a device address
+void printAddress(DeviceAddress deviceAddress)
+{
+  for (uint8_t i = 0; i < 8; i++)
+  {
+    // zero pad the address if necessary
+    if (deviceAddress[i] < 16) Serial.print("0");
+    Serial.print(deviceAddress[i], HEX);
+  }
+}
+
+// function to print the temperature for a device
+void printTemperature(DeviceAddress deviceAddress)
+{
+  float tempC = sensors.getTempC(deviceAddress);
+  Serial.print("Temp C: ");
+  Serial.print(tempC);
+  Serial.print(" Temp F: ");
+  Serial.print(DallasTemperature::toFahrenheit(tempC));
+}
+
+// function to print a device's resolution
+void printResolution(DeviceAddress deviceAddress)
+{
+  Serial.print("Resolution: ");
+  Serial.print(sensors.getResolution(deviceAddress));
+  Serial.println();    
+}
+
+// main function to print information about a device
+void printData(DeviceAddress deviceAddress)
+{
+  Serial.print("Device Address: ");
+  printAddress(deviceAddress);
+  Serial.print(" ");
+  printTemperature(deviceAddress);
+  Serial.println();
+}
+
+void loop(void)
+{ 
+  // call sensors.requestTemperatures() to issue a global temperature 
+  // request to all devices on the bus
+  Serial.print("Requesting temperatures...");
+  sensors.requestTemperatures();
+  Serial.println("DONE");
+
+  // print the device information
+  printData(insideThermometer);
+  printData(outsideThermometer);
+}
+\r