reprap config.h und slic3r config
authorBernhard Tittelbach <xro@realraum.at>
Wed, 10 Jul 2013 14:12:48 +0000 (14:12 +0000)
committerBernhard Tittelbach <xro@realraum.at>
Wed, 10 Jul 2013 14:12:48 +0000 (14:12 +0000)
reprap_mendel_prusa/teacup_firmware/config.h
reprap_mendel_prusa/teacup_firmware/extruder/config.h

index 4f015d9..696ac55 100644 (file)
 */
 //#define      STEPS_PER_M_X                                   10047
 //#define      STEPS_PER_M_X                                   8000
-//rechnerisch 8000, experimentell auf der X-Achse 7684.8395
-#define        STEPS_PER_M_X                               7685
+//rechnerisch 8000, experimentell auf der X-Achse 8963.59
+//rechnerisch 8000, experimentell auf der X-Achse 8075.67
+#define        STEPS_PER_M_X                               8050
 // 200 steps / 20 gearteeth / 2.5mm (abtsand zahnriemen-zähne)
 //#define      STEPS_PER_M_Y                                   10047
 //#define      STEPS_PER_M_Y                                   8000
-//rechnerisch 8000, experimentell auf der Y-Achse 6766.1691
-#define        STEPS_PER_M_Y                                   6766
+//rechnerisch 8000, experimentell auf der Y-Achse 7960.0
+#define        STEPS_PER_M_Y                                   7960
 //160000 für single step mit M8 Muttern, 320000 für half-step mit M8 Muttern
 //200 steps / 1.25 * 1000 * 2
 #define        STEPS_PER_M_Z                                   320000
@@ -88,9 +89,7 @@
 // Extruder gear ratio Gr = 14.0 / 43.0
 // STEPS_PER_M_E = 1m / (Gr * u_schraube) * motor_steps ¨~= 27933
 //#define      STEPS_PER_M_E           27933
-//experimentell 220mm:
-//#define      STEPS_PER_M_E   109400  
-//experimentell 200mm:
+//experimentell (ohne Düse) mit 200mm:
 #define        STEPS_PER_M_E   99455
 
 
 #define        X_MAX                   180.0
 
 #define        Y_MIN                   0.0
-#define        Y_MAX                   220.0
+#define        Y_MAX                   195.0
 
 #define        Z_MIN                   0.0
 #define        Z_MAX                   125.0
@@ -396,6 +395,7 @@ DEFINE_TEMP_SENSOR(bed,       TT_INTERCOM,    AIO1,      0)
 // workaround for heated bed over intercom. HEATER_EXTRUDER, HEATER_BED are the intercom temp channel numbers.
 #define        HEATER_EXTRUDER 0
 #define HEATER_BED 1
+#define HEATER_FAN 2
 
 
 
index 8faa6e8..42a9313 100644 (file)
@@ -78,9 +78,10 @@ DEFINE_TEMP_SENSOR(noheater, TT_THERMISTOR,          TRIM_POT_CHANNEL,               0)
 //~ //original code\r
 //~ DEFINE_HEATER(extruder,    DIO11)\r
 //~ DEFINE_HEATER(bed,                 AIO1)\r
-// r3: exchange HEATER and BED (we don't have bed right now, and heater-mosfet is shot)\r
+// r3: exchange HEATER and BED\r
 DEFINE_HEATER(extruder,        AIO1)\r
 DEFINE_HEATER(bed,                     DIO11)\r
+DEFINE_HEATER(fan,                     DIO12)\r
 #endif\r
 \r
 // list of PWM-able pins and corresponding timers\r