to github

[svn42.git] / rf433ctl / DallasTemperature / examples / Multiple / Multiple.pde

diff --git a/rf433ctl/DallasTemperature/examples/Multiple/Multiple.pde b/rf433ctl/DallasTemperature/examples/Multiple/Multiple.pde
deleted file mode 100644 (file)
index 2694d07..0000000
--- a/rf433ctl/DallasTemperature/examples/Multiple/Multiple.pde
+++ /dev/null
@@ -1,140 +0,0 @@
-#include <OneWire.h>
-#include <DallasTemperature.h>
-
-// Data wire is plugged into port 2 on the Arduino
-#define ONE_WIRE_BUS 3
-#define TEMPERATURE_PRECISION 9
-
-// Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
-OneWire oneWire(ONE_WIRE_BUS);
-
-// Pass our oneWire reference to Dallas Temperature. 
-DallasTemperature sensors(&oneWire);
-
-// arrays to hold device addresses
-DeviceAddress insideThermometer, outsideThermometer;
-
-void setup(void)
-{
-  // start serial port
-  Serial.begin(9600);
-  Serial.println("Dallas Temperature IC Control Library Demo");
-
-  // Start up the library
-  sensors.begin();
-
-  // locate devices on the bus
-  Serial.print("Locating devices...");
-  Serial.print("Found ");
-  Serial.print(sensors.getDeviceCount(), DEC);
-  Serial.println(" devices.");
-
-  // report parasite power requirements
-  Serial.print("Parasite power is: "); 
-  if (sensors.isParasitePowerMode()) Serial.println("ON");
-  else Serial.println("OFF");
-
-  // assign address manually.  the addresses below will beed to be changed
-  // to valid device addresses on your bus.  device address can be retrieved
-  // by using either oneWire.search(deviceAddress) or individually via
-  // sensors.getAddress(deviceAddress, index)
-  //insideThermometer = { 0x28, 0x1D, 0x39, 0x31, 0x2, 0x0, 0x0, 0xF0 };
-  //outsideThermometer   = { 0x28, 0x3F, 0x1C, 0x31, 0x2, 0x0, 0x0, 0x2 };
-
-  // search for devices on the bus and assign based on an index.  ideally,
-  // you would do this to initially discover addresses on the bus and then 
-  // use those addresses and manually assign them (see above) once you know 
-  // the devices on your bus (and assuming they don't change).
-  // 
-  // method 1: by index
-  if (!sensors.getAddress(insideThermometer, 0)) Serial.println("Unable to find address for Device 0"); 
-  if (!sensors.getAddress(outsideThermometer, 1)) Serial.println("Unable to find address for Device 1"); 
-
-  // method 2: search()
-  // search() looks for the next device. Returns 1 if a new address has been
-  // returned. A zero might mean that the bus is shorted, there are no devices, 
-  // or you have already retrieved all of them.  It might be a good idea to 
-  // check the CRC to make sure you didn't get garbage.  The order is 
-  // deterministic. You will always get the same devices in the same order
-  //
-  // Must be called before search()
-  //oneWire.reset_search();
-  // assigns the first address found to insideThermometer
-  //if (!oneWire.search(insideThermometer)) Serial.println("Unable to find address for insideThermometer");
-  // assigns the seconds address found to outsideThermometer
-  //if (!oneWire.search(outsideThermometer)) Serial.println("Unable to find address for outsideThermometer");
-
-  // show the addresses we found on the bus
-  Serial.print("Device 0 Address: ");
-  printAddress(insideThermometer);
-  Serial.println();
-
-  Serial.print("Device 1 Address: ");
-  printAddress(outsideThermometer);
-  Serial.println();
-
-  // set the resolution to 9 bit
-  sensors.setResolution(insideThermometer, 9);
-  sensors.setResolution(outsideThermometer, 9);
-
-  Serial.print("Device 0 Resolution: ");
-  Serial.print(sensors.getResolution(insideThermometer), DEC); 
-  Serial.println();
-
-  Serial.print("Device 1 Resolution: ");
-  Serial.print(sensors.getResolution(outsideThermometer), DEC); 
-  Serial.println();
-}
-
-// function to print a device address
-void printAddress(DeviceAddress deviceAddress)
-{
-  for (uint8_t i = 0; i < 8; i++)
-  {
-    // zero pad the address if necessary
-    if (deviceAddress[i] < 16) Serial.print("0");
-    Serial.print(deviceAddress[i], HEX);
-  }
-}
-
-// function to print the temperature for a device
-void printTemperature(DeviceAddress deviceAddress)
-{
-  float tempC = sensors.getTempC(deviceAddress);
-  Serial.print("Temp C: ");
-  Serial.print(tempC);
-  Serial.print(" Temp F: ");
-  Serial.print(DallasTemperature::toFahrenheit(tempC));
-}
-
-// function to print a device's resolution
-void printResolution(DeviceAddress deviceAddress)
-{
-  Serial.print("Resolution: ");
-  Serial.print(sensors.getResolution(deviceAddress));
-  Serial.println();    
-}
-
-// main function to print information about a device
-void printData(DeviceAddress deviceAddress)
-{
-  Serial.print("Device Address: ");
-  printAddress(deviceAddress);
-  Serial.print(" ");
-  printTemperature(deviceAddress);
-  Serial.println();
-}
-
-void loop(void)
-{ 
-  // call sensors.requestTemperatures() to issue a global temperature 
-  // request to all devices on the bus
-  Serial.print("Requesting temperatures...");
-  sensors.requestTemperatures();
-  Serial.println("DONE");
-
-  // print the device information
-  printData(insideThermometer);
-  printData(outsideThermometer);
-}
-\r