reprap config.h und slic3r config

[reprap_mendel_prusa.git] / teacup_firmware / config.h

diff --git a/teacup_firmware/config.h b/teacup_firmware/config.h
index 6fbaa3c..696ac55 100644 (file)
--- a/teacup_firmware/config.h
+++ b/teacup_firmware/config.h
@@ -64,12 +64,14 @@
 */
 //#define      STEPS_PER_M_X                                   10047
 //#define      STEPS_PER_M_X                                   8000
-#define        STEPS_PER_M_X                                   6766
+//rechnerisch 8000, experimentell auf der X-Achse 8963.59
+//rechnerisch 8000, experimentell auf der X-Achse 8075.67
+#define        STEPS_PER_M_X                               8050
 // 200 steps / 20 gearteeth / 2.5mm (abtsand zahnriemen-zähne)
 //#define      STEPS_PER_M_Y                                   10047
 //#define      STEPS_PER_M_Y                                   8000
-//rechnerisch 8000, experimentell auf der Y-Achse 6766.1691
-#define        STEPS_PER_M_Y                                   6766
+//rechnerisch 8000, experimentell auf der Y-Achse 7960.0
+#define        STEPS_PER_M_Y                                   7960
 //160000 für single step mit M8 Muttern, 320000 für half-step mit M8 Muttern
 //200 steps / 1.25 * 1000 * 2
 #define        STEPS_PER_M_Z                                   320000
@@ -87,9 +89,7 @@
 // Extruder gear ratio Gr = 14.0 / 43.0
 // STEPS_PER_M_E = 1m / (Gr * u_schraube) * motor_steps ¨~= 27933
 //#define      STEPS_PER_M_E           27933
-//experimentell 220mm:
-//#define      STEPS_PER_M_E   109400  
-//experimentell 200mm:
+//experimentell (ohne Düse) mit 200mm:
 #define        STEPS_PER_M_E   99455
 
 
@@ -127,10 +127,12 @@
 */
 
 #define        X_MIN                   0.0
-#define        X_MAX                   184.0
+// eigentlich 184mm, aber wir lassen uns ein bisschen Sicherheitsabstand
+//#define      X_MAX                   184.0
+#define        X_MAX                   180.0
 
 #define        Y_MIN                   0.0
-#define        Y_MAX                   220.0
+#define        Y_MAX                   195.0
 
 #define        Z_MIN                   0.0
 #define        Z_MAX                   125.0
@@ -140,7 +142,7 @@
 
        This is the startup default and can be changed with M82/M83 while running.
 */
-// #define E_ABSOLUTE
+#define E_ABSOLUTE
 
 
 
@@ -227,8 +229,8 @@
 
 #define        Y_STEP_PIN                                              DIO23
 #define        Y_DIR_PIN                                                       DIO22
-//~ #define    Y_MIN_PIN                                                       AIO6
-#define        Y_MAX_PIN                                                       AIO5
+#define        Y_MIN_PIN                                                       AIO6
+//~ #define    Y_MAX_PIN                                                       AIO5
 #define        Y_ENABLE_PIN                                    AIO7
 //#define      Y_INVERT_DIR
 //~ #define    Y_INVERT_MIN
@@ -255,7 +257,7 @@
 #define        SD_WRITE_PROTECT                        DIO3
 
 //#define      PS_ON_PIN                                                       DIO14
-#define        PS_ON_PIN                                                       PD4 // on TechZoneComm Motherboard, JTAG Port, TDI Pin
+#define        PS_ON_PIN                                                       PB5 // on TechZoneComm Motherboard, SPI Port: MOSI
 //#define      STEPPER_ENABLE_PIN              xxxx
 //#define      STEPPER_INVERT_ENABLE
 
@@ -390,11 +392,10 @@ DEFINE_TEMP_SENSOR(bed,       TT_INTERCOM,    AIO1,      0)
        I have searched high and low for a way to make the preprocessor do this for us, but so far I have not found a way.
 */
 
-//#define      HEATER_EXTRUDER HEATER_extruder
+// workaround for heated bed over intercom. HEATER_EXTRUDER, HEATER_BED are the intercom temp channel numbers.
 #define        HEATER_EXTRUDER 0
-
-// workaround for heated bed over intercom. HEATER_BED is the intercom temp channel number.
 #define HEATER_BED 1
+#define HEATER_FAN 2