From a501b777105ebdc03cbfdaa7be9a69f3898e46e8 Mon Sep 17 00:00:00 2001 From: Bernhard Tittelbach Date: Wed, 10 Jul 2013 14:12:48 +0000 Subject: [PATCH] reprap config.h und slic3r config --- teacup_firmware/config.h | 16 ++++++++-------- teacup_firmware/extruder/config.h | 3 ++- 2 files changed, 10 insertions(+), 9 deletions(-) diff --git a/teacup_firmware/config.h b/teacup_firmware/config.h index 4f015d9..696ac55 100644 --- a/teacup_firmware/config.h +++ b/teacup_firmware/config.h @@ -64,13 +64,14 @@ */ //#define STEPS_PER_M_X 10047 //#define STEPS_PER_M_X 8000 -//rechnerisch 8000, experimentell auf der X-Achse 7684.8395 -#define STEPS_PER_M_X 7685 +//rechnerisch 8000, experimentell auf der X-Achse 8963.59 +//rechnerisch 8000, experimentell auf der X-Achse 8075.67 +#define STEPS_PER_M_X 8050 // 200 steps / 20 gearteeth / 2.5mm (abtsand zahnriemen-zähne) //#define STEPS_PER_M_Y 10047 //#define STEPS_PER_M_Y 8000 -//rechnerisch 8000, experimentell auf der Y-Achse 6766.1691 -#define STEPS_PER_M_Y 6766 +//rechnerisch 8000, experimentell auf der Y-Achse 7960.0 +#define STEPS_PER_M_Y 7960 //160000 für single step mit M8 Muttern, 320000 für half-step mit M8 Muttern //200 steps / 1.25 * 1000 * 2 #define STEPS_PER_M_Z 320000 @@ -88,9 +89,7 @@ // Extruder gear ratio Gr = 14.0 / 43.0 // STEPS_PER_M_E = 1m / (Gr * u_schraube) * motor_steps ¨~= 27933 //#define STEPS_PER_M_E 27933 -//experimentell 220mm: -//#define STEPS_PER_M_E 109400 -//experimentell 200mm: +//experimentell (ohne Düse) mit 200mm: #define STEPS_PER_M_E 99455 @@ -133,7 +132,7 @@ #define X_MAX 180.0 #define Y_MIN 0.0 -#define Y_MAX 220.0 +#define Y_MAX 195.0 #define Z_MIN 0.0 #define Z_MAX 125.0 @@ -396,6 +395,7 @@ DEFINE_TEMP_SENSOR(bed, TT_INTERCOM, AIO1, 0) // workaround for heated bed over intercom. HEATER_EXTRUDER, HEATER_BED are the intercom temp channel numbers. #define HEATER_EXTRUDER 0 #define HEATER_BED 1 +#define HEATER_FAN 2 diff --git a/teacup_firmware/extruder/config.h b/teacup_firmware/extruder/config.h index 8faa6e8..42a9313 100644 --- a/teacup_firmware/extruder/config.h +++ b/teacup_firmware/extruder/config.h @@ -78,9 +78,10 @@ DEFINE_TEMP_SENSOR(noheater, TT_THERMISTOR, TRIM_POT_CHANNEL, 0) //~ //original code //~ DEFINE_HEATER(extruder, DIO11) //~ DEFINE_HEATER(bed, AIO1) -// r3: exchange HEATER and BED (we don't have bed right now, and heater-mosfet is shot) +// r3: exchange HEATER and BED DEFINE_HEATER(extruder, AIO1) DEFINE_HEATER(bed, DIO11) +DEFINE_HEATER(fan, DIO12) #endif // list of PWM-able pins and corresponding timers -- 1.7.10.4