From 49feb10d810bc2f36ba6289146721b4e804efcf9 Mon Sep 17 00:00:00 2001 From: Bernhard Tittelbach Date: Sun, 7 Jul 2013 01:25:28 +0000 Subject: [PATCH] reprap teacup firmware config update --- teacup_firmware/config.h | 25 ++++++++++++++++++++----- teacup_firmware/extruder/config.h | 17 +++++++++++++---- 2 files changed, 33 insertions(+), 9 deletions(-) diff --git a/teacup_firmware/config.h b/teacup_firmware/config.h index bab04fe..6fbaa3c 100644 --- a/teacup_firmware/config.h +++ b/teacup_firmware/config.h @@ -75,9 +75,23 @@ #define STEPS_PER_M_Z 320000 /// http://blog.arcol.hu/?p=157 may help with this one -#define STEPS_PER_M_E 35200 +//#define STEPS_PER_M_E 35200 // Extruder gear ratio Gr = 14.0 / 43.0 -// Extruder nozzle diameter = 0.5 (? oder 0.35, oder 0.25) +// Extruder nozzle diameter = 0.5mm (bzw 0.35mm mit unserer anderen Düse) +// Filament Width = 3mm + + +// d_schraube ~= 0.007m +// u_schraube = d_schraube * pi ~= 0.022m +// motor_steps for 1 circumfence = 200 +// Extruder gear ratio Gr = 14.0 / 43.0 +// STEPS_PER_M_E = 1m / (Gr * u_schraube) * motor_steps ¨~= 27933 +//#define STEPS_PER_M_E 27933 +//experimentell 220mm: +//#define STEPS_PER_M_E 109400 +//experimentell 200mm: +#define STEPS_PER_M_E 99455 + /* Values depending on the capabilities of your stepper motors and other mechanics. @@ -204,7 +218,7 @@ #define X_STEP_PIN DIO15 #define X_DIR_PIN DIO18 //~ #define X_MIN_PIN DIO20 -//~ #define X_MAX_PIN DIO21 +#define X_MAX_PIN DIO21 #define X_ENABLE_PIN DIO19 //#define X_INVERT_DIR //~ #define X_INVERT_MIN @@ -241,7 +255,7 @@ #define SD_WRITE_PROTECT DIO3 //#define PS_ON_PIN DIO14 -#define PS_ON_PIN PD4 // on TCC Motherboard, JTAG Port, TDI Pin +#define PS_ON_PIN PD4 // on TechZoneComm Motherboard, JTAG Port, TDI Pin //#define STEPPER_ENABLE_PIN xxxx //#define STEPPER_INVERT_ENABLE @@ -376,7 +390,8 @@ DEFINE_TEMP_SENSOR(bed, TT_INTERCOM, AIO1, 0) I have searched high and low for a way to make the preprocessor do this for us, but so far I have not found a way. */ -// #define HEATER_EXTRUDER HEATER_extruder +//#define HEATER_EXTRUDER HEATER_extruder +#define HEATER_EXTRUDER 0 // workaround for heated bed over intercom. HEATER_BED is the intercom temp channel number. #define HEATER_BED 1 diff --git a/teacup_firmware/extruder/config.h b/teacup_firmware/extruder/config.h index c842060..8faa6e8 100644 --- a/teacup_firmware/extruder/config.h +++ b/teacup_firmware/extruder/config.h @@ -54,8 +54,13 @@ #define TEMP_THERMISTOR -#define HEATER_PIN DIO11 -#define BED_PIN AIO1 +//~ //original code +//~ #define HEATER_PIN DIO11 +//~ #define BED_PIN AIO1 +//~ #define FAN_PIN DIO12 +// r3: exchange HEATER and BED (we don't have bed right now, and heater-mosfet is shot) +#define BED_PIN DIO11 +#define HEATER_PIN AIO1 #define FAN_PIN DIO12 // extruder settings @@ -70,8 +75,12 @@ DEFINE_TEMP_SENSOR(noheater, TT_THERMISTOR, TRIM_POT_CHANNEL, 0) #endif #ifdef DEFINE_HEATER -DEFINE_HEATER(extruder, DIO11) -DEFINE_HEATER(bed, AIO1) +//~ //original code +//~ DEFINE_HEATER(extruder, DIO11) +//~ DEFINE_HEATER(bed, AIO1) +// r3: exchange HEATER and BED (we don't have bed right now, and heater-mosfet is shot) +DEFINE_HEATER(extruder, AIO1) +DEFINE_HEATER(bed, DIO11) #endif // list of PWM-able pins and corresponding timers -- 1.7.10.4