From: Bernhard Tittelbach <xro@realraum.at>
Date: Tue, 20 Aug 2013 03:07:47 +0000 (+0000)
Subject: identical num steps on x and y, longer delay between onewire access
X-Git-Url: https://git.realraum.at/?a=commitdiff_plain;h=79613199100e15d05084f4e1b1ede0a1a25259b3;p=svn42.git

identical num steps on x and y, longer delay between onewire access
---

diff --git a/reprap_mendel_prusa/teacup_firmware/config.h b/reprap_mendel_prusa/teacup_firmware/config.h
index 2b4f9fb..e829616 100644
--- a/reprap_mendel_prusa/teacup_firmware/config.h
+++ b/reprap_mendel_prusa/teacup_firmware/config.h
@@ -66,12 +66,12 @@
 //#define   STEPS_PER_M_X                   8000
 //rechnerisch 8000, experimentell auf der X-Achse 8963.59
 //rechnerisch 8000, experimentell auf der X-Achse 8075.67
-#define STEPS_PER_M_X                   8200
+#define STEPS_PER_M_X                   8000
 // 200 steps / 20 gearteeth / 2.5mm (abtsand zahnriemen-zähne)
 //#define   STEPS_PER_M_Y                   10047
-//#define   STEPS_PER_M_Y                   8000
+#define   STEPS_PER_M_Y                   8000
 //rechnerisch 8000, experimentell auf der Y-Achse 8164.0
-#define STEPS_PER_M_Y                   8110
+//#define STEPS_PER_M_Y                   8110
 //160000 für single step mit M8 Muttern, 320000 für half-step mit M8 Muttern
 //200 steps / 1.25 * 1000 * 2
 #define STEPS_PER_M_Z                   320000
diff --git a/reprap_mendel_prusa/teacup_firmware/extruder/config.h b/reprap_mendel_prusa/teacup_firmware/extruder/config.h
index 474b971..ace2d67 100644
--- a/reprap_mendel_prusa/teacup_firmware/extruder/config.h
+++ b/reprap_mendel_prusa/teacup_firmware/extruder/config.h
@@ -74,11 +74,11 @@
 DEFINE_TEMP_SENSOR(extruder,    TT_THERMISTOR,      TEMP_PIN_CHANNEL,       THERMISTOR_EXTRUDER)
 //DEFINE_TEMP_SENSOR(bed,           TT_THERMISTOR,      TEMP_BED_PIN_CHANNEL,   THERMISTOR_EXTRUDER)
     //9 bits accuracy for faster conversion time
-DEFINE_TEMP_SENSOR(bed,         TT_ONEWIRE,     0,  9)
+DEFINE_TEMP_SENSOR(bed,         TT_DS1820,     0,  12)
 // dummy temp sensor so analog_mask includes trim pot
 DEFINE_TEMP_SENSOR(noheater,    TT_THERMISTOR,      TRIM_POT_CHANNEL,       0)
 #endif
-// DEFINE_HEATER(<name>, <pin>, <fan startup threshold pwm value>)
+// DEFINE_HEATER(<name>, <pin>, <invert?>, <fan startup threshold pwm value>)
 // fan startup threshold: FANs usually take more power to start spinning than to keep spinning,
 //                        so, below a given pwm value we start the fan with full power and after
 //                        50ms lower the output to the requested value.