X-Git-Url: https://git.realraum.at/?a=blobdiff_plain;ds=sidebyside;f=teacup_firmware%2Fconfig.h;h=c19a5021368863b1dfcfa14b90d5bd3b267a21bd;hb=e44e0588ead1ab6341b959e7b24bef899b6bce5e;hp=bbce7dee295eecf8fd0c68cddf8e2b29457f2935;hpb=8eea2dd03e91403559971bdce3f29e6baa338d89;p=reprap_mendel_prusa.git

diff --git a/teacup_firmware/config.h b/teacup_firmware/config.h
index bbce7de..c19a502 100644
--- a/teacup_firmware/config.h
+++ b/teacup_firmware/config.h
@@ -64,13 +64,14 @@
 */
 //#define	STEPS_PER_M_X					10047
 //#define	STEPS_PER_M_X					8000
-//rechnerisch 8000, experimentell auf der X-Achse 7684.8395
-#define	STEPS_PER_M_X				    7685
+//rechnerisch 8000, experimentell auf der X-Achse 8963.59
+//rechnerisch 8000, experimentell auf der X-Achse 8075.67
+#define	STEPS_PER_M_X				    8050
 // 200 steps / 20 gearteeth / 2.5mm (abtsand zahnriemen-zähne)
 //#define	STEPS_PER_M_Y					10047
 //#define	STEPS_PER_M_Y					8000
-//rechnerisch 8000, experimentell auf der Y-Achse 6766.1691
-#define	STEPS_PER_M_Y					6766
+//rechnerisch 8000, experimentell auf der Y-Achse 8164.0
+#define	STEPS_PER_M_Y					8164
 //160000 für single step mit M8 Muttern, 320000 für half-step mit M8 Muttern
 //200 steps / 1.25 * 1000 * 2
 #define	STEPS_PER_M_Z					320000
@@ -88,10 +89,8 @@
 // Extruder gear ratio Gr = 14.0 / 43.0
 // STEPS_PER_M_E = 1m / (Gr * u_schraube) * motor_steps ¨~= 27933
 //#define	STEPS_PER_M_E		27933
-//experimentell 220mm:
-//#define	STEPS_PER_M_E	109400  
-//experimentell 200mm:
-#define	STEPS_PER_M_E	99455
+//experimentell (ohne Düse): 99455 previousvalue *(200.0mm software/194.0mm echt) = 102530.93
+#define	STEPS_PER_M_E	102531
 
 
 /*
@@ -133,7 +132,7 @@
 #define	X_MAX			180.0
 
 #define	Y_MIN			0.0
-#define	Y_MAX			220.0
+#define	Y_MAX			195.0
 
 #define	Z_MIN			0.0
 #define	Z_MAX			125.0
@@ -393,11 +392,10 @@ DEFINE_TEMP_SENSOR(bed,       TT_INTERCOM,    AIO1,      0)
 	I have searched high and low for a way to make the preprocessor do this for us, but so far I have not found a way.
 */
 
-//#define	HEATER_EXTRUDER HEATER_extruder
+// workaround for heated bed over intercom. HEATER_EXTRUDER, HEATER_BED are the intercom temp channel numbers.
 #define	HEATER_EXTRUDER 0
-
-// workaround for heated bed over intercom. HEATER_BED is the intercom temp channel number.
 #define HEATER_BED 1
+#define HEATER_FAN 2